SATO GL 4xxe Series Guía de usuario

RFID KIT USER GUIDE GL 4xxe Series For printer models: Read this User Guide before and during the operation of the above accessory. Keep this Guide ha

10 Introduction to the RFID configuration optionsTag Write Cnt Displays the number of tags attempted to be writte

11 Admin User Menu Items (GL4xxe)These menu items are visible only when the Admin User option is set to Enab

12 Read Tag Reads the tag in range of the internal RFID coupler and reports the tag data to the debug

13 Table 4. Printed Overstrike Error MessagesError Message ExplanationTag R/W Err x Check media Ta g C

14 Write Power This menu item selects the write power level to be used in the RFID encoder. 1 is the low

15 Tag Class Selects the class of the custom tag. Class 0+, Class 1.19, Gen 2, and Class Zuma tags are r

16 Scan Start Pos Determines where on the label the RFID calibration will begin. By default, the calibration proce

17 Requesting AnRFID ReportThis procedure prints a summarized RFID report. (This report also includes validator data

18 Advanced RFID CalibrationTag ProfilerRead and Write power settings can be optimized using the Tag Profiler. Before running the Tag Profiler, it

19 • Custom (Cal) Max Power. Sets the upper level that will be tested during calibration. To speed up calibra

2 1 General Important information This quick guide provides important information on how to setup your new SATO product. Be sure to read th

20 2．RFID Command Specification With the SATO GL4XXe, it is possible to return RFID information before writing data. The printer

21 ESC+IP0 Command ESC IP0 Parameter Hex code <1B>16 <49>16<50>16<30>16 e, d, k, a, u, m, f,p, s, t, c, n Initial value

22 c = total number of digits for company prefix (Should be any value with 6 to 12 according to the number of digits of ‘s’ or ‘t’ parameters) n =

23 【Example 5】 Description: This example illustrates to write EAN 128 data to the tag. Data: ＜A＞ ＜V＞50＜H＞50＜X22＞,3114F536CCCE4C3097000000 ＜IP0＞e:a

24 5． The optional parameters could be omitted. Refer the table bellow to find optional parameters. parameters Gen2 e: EPC Type [F***]ａ (EAN12

25 [Function] This is a control function for reading data from the EPC code-compatible RFID tag. [Format] <IP1> ,b:X; Where ,

26 [Return Status Example 1] When [8000 0000 4000 0001] is saved in an EPC-compatible tag. 02 Start code 38 30 30 30 30 30 30 30 34 30 30 30

27 ESC+TM ESC TM Parameter Hexadecimal code <1B>16 <54>16<4D>16 X Initial value Nil When power switch is OFF The set parame

28 ESC+F ESC F Parameter Hexadecimal code <1B>16 <46>16 a a a a b c c c c, d d, e e, f Initial value Nil When power switch is OFF

29 [Coding Example 2] Write EPC and User memory Number of times to repeat the same data : 1, incrementing :+, step of sequence:100,Number of d

3 1.2 Explanation of symbols This instruction manual uses various warning icons to help you understand the safe operation of your printer. Expla

30 3. GL RFID Coupler Design The GL4xxe RFID has a coupler design that supports a greater variety of tag types. You can move the coupler horizont

31 4. Adjusting the Coupler position Remove the thumbscrew that secures the lower front cover to the printer.

32 Use the coupler handle to adjust the coupler so that the coupler position indicator points to the correct color on the colored position strip.

33 Error Message Explanation Solution NON-RFID DATA On Rfid Tag A job was printed that had no RFID commands on at least one form of the job whi

34 Symptom Solution No communication between the printer and the reader 1. Make sure Reader = Enable in the RFID (or RFI

35

41.3 Contact and Document Information For SATO oce locations worldwide. please visit www.satoworldwide.comVersion: GBS-GL4xxe-01rA-13-06-0

5 Overview This User Manual describes the operation and programming procedures for RFID smart labels (with emb

6 1. Introduction to the RFID configuration optionsRFID CONTROL Menu (GL4xxe Series) RFID CONTROL Error Handling Overstrike* None

7 ...continued from previous page RFID CONTROL Custom Setting Non-RFIDWarning Disable* Enable Custom Tag Du

8 Introduction to the RFID configuration options RFID Menu Items(GL4xxe) RFID Reader This menu item enables or

9 Table 3. Supported RFID TagTypes (GL4xxe)Tag Name Bits Protocol TagClass Menu Selection KSW Gen 2 Exca