SATO CG4 Series Manual de instrucciones Pagina 8
- Pagina / 102
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Table of Contents
Page 2 CG4 Series Operator Manual
Appendix........................................................................................................................8 - 1
8.1 Optional Accessories - Cutter........................................................................................... 8 - 2
8.2 Optional Accessories - Dispenser .................................................................................... 8 - 3
8.3 Positions of sensors and options...................................................................................... 8 - 5
8.4 Operation Mode Selection................................................................................................ 8 - 6
8.5 Base Reference Point ...................................................................................................... 8 - 7
8.6 Offset position Adjustment ............................................................................................... 8 - 9
8.7 Paper End ...................................................................................................................... 8 - 10
8.8 Ribbon End .................................................................................................................... 8 - 11
SATO Group of Companies ......................................................................................... 9 - 1
SATO Group of Companies ................................................................................................... 9 - 2
- Operator Manual 1
- SATO America, Inc 2
- Safety Precautions 3
- Select a Safe Location 5
- Power Supply 5
- Table of Contents 7
- INTRODUCTION 9
- 1.2.1 Included Accessories 10
- 1.3 PARTS IDENTIFICATION 11
- Back view 12
- Section 1: Introduction 14
- INSTALLATION 15
- 2.2 MEDIA SELECTION 16
- 2.1 SITE LOCATION 16
- 2.3 LOADING LABELS 17
- 2.3 LOADING LABELS (cont’d) 18
- Roll media (Face-in) 20
- Roll media (Face-out) 20
- Fan-fold media 20
- (Printed side face up) 20
- Ribbon unit 21
- Ribbon route 23
- 2.5 CONNECTIONS 24
- 2.5 CONNECTIONS (cont’d) 27
- 2.5.5 Turning On the Power 27
- 2.5.6 Turning Off the Power 27
- Section 2: Installation 28
- OPERATION AND CONFIGURATION 29
- 3.1 OPERATOR PANEL 30
- 3.2 OPERATING MODES 31
- 3.3 USER TEST PRINT MODE 32
- Offset value (Vertical and 33
- Pitch offset value ±099 DOT 33
- 3.4 FACTORY TEST PRINT MODE 36
- Base reference correction 38
- 3.5 OPERATION SETTING MODE 39
- OPERATION SETTING MODE 40
- 3.6 PROGRAM DOWNLOAD MODE 41
- 3.6.1 Firmware Download 42
- 3.7 FONT DOWNLOAD MODE 43
- 3.8 DEFAULT SETTING MODE 44
- 3.9 HEX DUMP MODE 45
- TROUBLESHOOTING 49
- Incorrect 50
- Download 50
- TROUBLESHOOTING TABLE 52
- LIGHT PRINT IMAGES 53
- UNEVEN PRINT DARKNESS 53
- SMEARED PRINT IMAGES 53
- MEANDERING MEDIA 53
- CHK TROUBLESHOOTING STEP 54
- 4.4.1 Hex Dump 55
- 4.4.2 Test label printing 55
- Section 4: Troubleshooting 56
- CLEANING AND MAINTENANCE 57
- I-Mark and Gap 59
- Media guide 59
- 5.4 EASY REPLACEMENT OF PARTS 60
- Fulcrum shaft 62
- Circular 62
- 5.5 ADJUSTING PRINT QUALITY 63
- GENERAL SPECIFICATIONS 65
- PHYSICAL CHARACTERISTICS 65
- POWER SUPPLY (AC ADAPTER) 65
- MODEL NAME 66
- BARCODE CAPABILITIES 69
- STANDARD FUNCTIONS 69
- HARDWARE AND RELATED 70
- REGULATORY COMPLIANCE 70
- CUTTER SPECIFICATIONS 71
- DISPENSER SPECIFICATIONS 71
- INTERFACE SPECIFICATIONS 73
- 7.2 RS232C SERIAL INTERFACE 74
- 7.2.2 Ready/Busy 76
- 7.2.3 X-ON/X-OFF 77
- 7.3.2 Pin Assignments 79
- 7.3.3 Input/Output Signals 80
- 7.4.2 Pin Assignments 81
- 7.4.3 Host Computer Settings 82
- 7.5.2 Software Specifications 84
- 7.5.3 TCP/IP Specifications 85
- 7.5.4 LPD Specifications 85
- 7.5.5 FTP Specifications 85
- 7.5.6 TELNET Specifications 86
- 7.5.7 Setting/Displayed Items 86
- APPENDIX 89
- 8.1.2 Cut position Adjustment 90
- Label output 92
- 8.4 OPERATION MODE SELECTION 94
- Continuous Mode 95
- Tear off Mode 95
- Cutter Mode 95
- Dispenser Mode 96
- Linerless (Non Sepa) Mode 96
- Base reference 97
- 8.7 PAPER END 98
- Feeds 50mm 99
- 8.7.2 Fanfold Label End 99
- Section 8: Appendix 100
- SATO GROUP OF COMPANIES 101
Relacionado con productos y manuales para Impresión y escaneo SATO CG4 Series
Impresión y escaneo SATO XL4xxe Manual de usuario
(114 paginas)
(114 paginas)
Impresión y escaneo SATO CL608 Especificaciones
(12 paginas)
(12 paginas)
Impresión y escaneo SATO GY412 Manual de instrucciones
(217 paginas)
(217 paginas)
Impresión y escaneo SATO XL400 Manual de usuario
(194 paginas)
(194 paginas)
Impresión y escaneo SATO M8485Se Manual de servicio
(216 paginas)
(216 paginas)
Impresión y escaneo SATO CG412TT Manual de usuario
(102 paginas)
(102 paginas)
Impresión y escaneo SATO XL4xxe Manual de usuario
(121 paginas)
(121 paginas)
(73 paginas)
Impresión y escaneo SATO M8450 Manual de usuario
(60 paginas)
(60 paginas)
(73 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.636 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales