SATO LP 100R L Guía de instalación

LP 100R Laser Printer Installation Guide Part No. 9855148

INSTALLATION GUIDE VIII Preface Purpose of This Guide To present installation instructions for the LP 100R printer. This guide provides all installati

INSTALLATION GUIDE i TABLE OF CONTENTS CHAPTER 1. PRELIMINARY INSTRUCTIONS ... 1 1.1 Operating Location Requ

INSTALLATION GUIDE ii TABLE OF CONTENTS, continued 4.5 Installation of the Suction Brake Unit ... 12 4.6 Installa

INSTALLATION GUIDE iii TABLE OF CONTENTS, continued CHAPTER 6. EQUIPMENT SPECIFICATION ... 37 CHAPTER 7. EQUIP

INSTALLATION GUIDE iv This page is intentionally blank.

INSTALLATION GUIDE 1 CHAPTER 1. Preliminary Instructions 1.1 Operating Location Requirements 1. Refer to Appendix A, “LP 100R Printer Operation L

INSTALLATION GUIDE 2 CHAPTER 2. Unpacking Instructions 2.1 Removing the Carton 1. Remove the straps from the carton as shown in Figure 2-1. 2.

INSTALLATION GUIDE 3 3. Lift the outer carton as shown in Figure 2-2 until the carton is clear of the printer. 4. Remove the ramp on the side of th

INSTALLATION GUIDE 4 2.2 Removal of Packing Material and Accessories Boxes 1. Remove the two accessories boxes from the stacker tray. 2. Raise t

INSTALLATION GUIDE 5 5. Utilizing four or more people, carefully move the printer down the ramp to the floor as shown in Figure 2-5. Figure 2

Revision number Date Reason for update Rev 0 March, 2009 Initial release Rev 1 April, 2014 USB Support, Company Info Copyright ©

INSTALLATION GUIDE 6 9. Open the fuser lamp assembly (2) screws. 10. Remove the shipping cushion on the fuser glass as shown in Figure 2-7. 11. R

INSTALLATION GUIDE 7 13. Open the front door. 14. Remove all visible tape as shown in Figure 2-8 below. 15. Remove the Toner Collecting Bottle and

INSTALLATION GUIDE 8 17. Remove the Lower Right Side Cover. 18. Remove the Controller and remove packing material around the controller. 19. Remo

INSTALLATION GUIDE 9 CHAPTER 3. Moving the Printer to the Operating Location 3.1 General Cautions 1. Use care not to damage the finish of the prin

INSTALLATION GUIDE 10 CHAPTER 4. Unpacking and Inventory of Accessories Boxes 4.1 Accessories Box No. 1 1. Unpack and inventory the content

INSTALLATION GUIDE 11 4.2 Accessories Box No. 2 1. Unpack and inventory the contents of accessories Box 2. 4.3 Access

INSTALLATION GUIDE 12 4.5 Installation of the Suction Brake Unit 1. Remove the Suction Brake, three mounting screws and two connector cover mount

INSTALLATION GUIDE 13 4.6 Installation of Web Guide/Connector Panel 1. Remove the filler plate (2 screws) from lower side cover beneath the suctio

INSTALLATION GUIDE 14 Installation of Web Guide/Connector Panel, continued 10. Position the Box Assembly under the suction brake of the printer lo

INSTALLATION GUIDE 15 CHAPTER 5. Electromechanical Setup Procedure Note: Parts of this chapter may have already been completed during printer prep.

Notice All rights are reserved for devices, circuits, techniques, software, and names appearing in this publication. SATO America, Inc. ("SA

INSTALLATION GUIDE 16 5.2 Preparation of the Developer Unit 1. Open the front door and slide open the EP Drawer (Figure 5-3.)

INSTALLATION GUIDE 17 5.2 Preparation of the Developer Unit, continued 3. Remove the Main Charge Unit as shown in Figure 5-5.

INSTALLATION GUIDE 18 5.2 Preparation of the Developer Unit, continued 5. Remove the Developer Unit from the EP Drawer as shown in Figure 5-7.

INSTALLATION GUIDE 19 5.2 Preparation of the Developer Unit, continued 7. Remove one of the developer powder boxes from accessories Box 2. 8. One

INSTALLATION GUIDE 20 5.2 Preparation of the Developer Unit, continued 12. Install the OPC Cartridge in the EP Drawer as shown in Figure 5-12.

INSTALLATION GUIDE 21 5.3 Controller Installation, Meto-Logic 1. Open lower Front Door. 2. Locate power strip above main power supply cabi

INSTALLATION GUIDE 22 5.3 Controller Installation, Meto-Logic, continued 5. Attach the AC power cord supplied from the AC output receptacle of the

INSTALLATION GUIDE 23 Power Strip 5.3 Controller Installation, Meto-Logic, continued 9. Attach the Blue TDU cable from the connector panel

INSTALLATION GUIDE 24 5.4 Storage of Test Print Samples 1. Test print samples printed during installation should be stored within the printer for

INSTALLATION GUIDE 25 5.4 Storage of Test Print Samples, continued Error Log:

Liability Disclaimer SATO America, Inc., products are warranted in accordance with the terms of the applicable SATO product specification. Product

INSTALLATION GUIDE 26 5.4 Storage of Test Print Samples, continued Character Fill:

INSTALLATION GUIDE 27 5.5 Power Cord Connection Note: If the printer is being installed in a country location other that the U.S. or Canada, it

INSTALLATION GUIDE 28 5.5 Power Cord Connection, continued 3. Plug the printer power cord into the wall outlet (Figure 5-20).

INSTALLATION GUIDE 29 5.6 Main Power-On 1. Place the printer circuit breaker in the ON position, (Figure 5-21). 5.7

INSTALLATION GUIDE 30 5.8 Entering Maintenance Mode 5.8.1 Turning the Controller's Power Off Before entering Maintenance mode you must firs

INSTALLATION GUIDE 31 5.8.2 Turning the Printer's Power On, Continued Note: After the warm-up sequence, the LCD display will boot to the Mai

INSTALLATION GUIDE 32 5.9 ATDC Adjustment • When replacing the developer unit or replacing the developer starter, it is necessary to adjust the c

INSTALLATION GUIDE 33 5.10 Toner Bottle Installation 1. Tap a new Toner Bottle against a desk or other hard surface four or five times as shown in

INSTALLATION GUIDE 34 5.10 Toner Bottle Installation, continued 4. With the “UP” marking on top, insert the Toner Bottle into position as shown

INSTALLATION GUIDE 35 5.11 Power Off 1. Place the Printer Power Switch (Refer to Figure 5-19) into the off position.

INSTALLATION GUIDE IIIRegulatory Notices Laser Safety This product employs a Class 3B laser diode having maximum power of 35 mW and wavelength of 770-

INSTALLATION GUIDE 36 5.12 Final Mechanical Check 1. After completing the installation, check the following mechanical functions. Check the o

INSTALLATION GUIDE 37 6.1 Equipment Specification Consult Appendix C for LP 100R Equipment Specifications. 7.1 Equipment Installation Checklist Pr

INSTALLATION GUIDE 38 This page is intentionally blank.

A P P E N D I X A A-1 LP 100R PRINTER OPERATING LOCATION REQUIREMENTS 1.1 Operating Location Requirements Before proceeding with the print

A P P E N D I X A A-2 1.1.3 Clearance Requirements 1.1.3.1 Printer Size Figure A-1 illustrates a front a

A P P E N D I X A A-3 1.1.3.2 Printer Clearance Requirements (Maintenance Area) Figure A-2 illustrates a printer top view showing the minimu

A P P E N D I X A A-4 1.1.3.3 Printer Clearance Requirements (Installed) Figure A-3 illustrates a printer top view showing the minimum c

A P P E N D I X A A-5 1.1.4 Operating Environment Requirements 1.1.4.1 Temperature 50° F to 95° F (10° C to 35° C) with a temperature varia

INSTALLATION GUIDE A-6 This page is intentionally blank.

A P P E N D I X B B-1 +20-10+20-10EUROPEAN POWER CONSIDERATIONS 1.1 POWER CORD INSTRUCTIONS (EUROPE) DANGER THIS APPARATUS IS SHIPP

INSTALLATION GUIDE IV FCC Regulations This equipment generates and uses radio frequency and, if not installed in accordance with the instruction manua

A P P E N D I X B B-2 1.1.2 CONFIGURE THE PLUG 1. If the power supply cord is not provided with an attachment plug cap, configure a new pl

A P P E N D I X C C-1 LP 100R PRINTER EQUIPMENT SPECIFICATIONS Item Description 1. Printing Method Dry Electro Photographic Laser Dio

A P P E N D I X C C-2 LP 100R PRINTER EQUIPMENT SPECIFICATIONS, continued Item Description 12. Power Source Universal (AC 200 to 240 VAC)

A P P E N D I X D D-1 LP 100R SWING GUIDE INSTALLATION 1.1 SWING GUIDE INSTALLATION PROCEDURE Packing list 1 Swing guide assembly

A P P E N D I X D D-2 SWING GUIDE INSTALLATION, CONTINUED 2. Remove the blind plate from the printer frame for the swing guide drive motor

A P P E N D I X D D-3 SWING GUIDE INSTALLATION, CONTINUED 7. Separate the two swing guide frame plates by removing the two thumb screws, and

A P P E N D I X D D-4 SWING GUIDE INSTALLATION, CONTINUED 11. Swing the front plate upward and secure up against the bottom frame of the pri

A P P E N D I X E E-1 LP 100R BURSTER UNIT INSTALLATION Packing list: 1 Burster unit 1 4 Fixing screws (4×8 mm) 2 2 Paper guide 1

A P P E N D I X E E-2 BURSTER UNIT INSTALLATION, CONTINUED 4. Remove the exit guide A by removing the four screws. (Figure E-3)

A P P E N D I X F F-1 LP 100R IPDS USB KEY INSTALLATION 1. To enable the IPDS Emulation, the Sentinel Key shown below must be installed int

INSTALLATION GUIDE VManufacturer’s Instructions The user must observe the following precautions in installing and operating this device: 1. Operate t

INSTALLATION GUIDE F-2 This page is intentionally blank.

A P P E N D I X G G-1 LP 100R PC CARTRIDGE INSTALLATION Packing list 1 PC drum 1 2 PC cleaning unit 1 3 Cleaner blade 1 Note1: Be

A P P E N D I X G G-2 LP 100 R PC CARTRIDGE INSTALLATION, CONTINUED 3. Re-install the Main Charger Unit as shown in Figure G-3. 4.

APPENDIX H LP 100R PRINTER EQUIPMENT INSTALLATION CHECKLIST In order to permit the SATO Printer Product Support Group to maintain an adequ

APPENDIX H LP 100R PRINTER EQUIPMENT INSTALLATION CHECKLIST CUSTOMER DATA Company Name: Company Address: Contact Name: Location of c

APPENDIX H Equipment Checklist, continued Customer Name: Were the following items received with the Printer? Accessory Box No.1,

II-3IIyyiiyIII APPENDIX H Equipment Checklist, continued Customer Name: Were any parts missing from the Printer or the Controller?

This page is intentionally blank.

APPENDIX H This page is intentionally blank.

INSTALLATION GUIDE VI DHHS This printer is certified as a Class 1 Laser Product under the United States Department of Health and Human Services (DHHS)

Published by: SATO America, Inc. LP 100R Installation Guide Publication ID # 9855148 March 2009 RELATED PUBLICATIONS LP 100R M

INSTALLATION GUIDE VIIGeneral Notes, Warnings, and Cautions Note: The LP 100R printer uses an electrophotographic printing system, which requires mor