SATO /gt Series Especificaciones descargar pdf (Pagina 46)

Section 3: Configuration and Operation

Page 3-10 GT Series Operator’s Manual

This setting determines whether the space surrounding each text

character is of a fixed width, or whether that space is to be varied to

be visually more pleasant.

Use the buttons to select either PROPORTIONAL or FIXED.

The default value is FIXED.

Press ENTER to confirm your selection and return to the main User

Mode screen. Press the FUNCTION or CANCEL key to exit the User Mode setting.

Note:

The subject fonts are from x21 to x24

1 2 ... 41 42 43 44 45 46 47 48 49 50 51 ... 151 152

OPERATOR’S MANUAL 1
TABLE OF CONTENTS 3
OVERVIEW 7
Feature GT408e GT412e GT424e 9
Section 1: Introduction 10
Specification/ 10
Model Name 10
GT408 GT412 GT424 10
INSTALLATION 13
SAFETY PRECAUTIONS 14
GENERAL PRECAUTIONS 15
SECTION 2: INSTALLATION 16
2.1 UNPACKING 16
Important! 17
2.1.2 PARTS IDENTIFICATION 18
Angled Front View 18
Front View 18
Rear View 19
Side View 20
(Media assembly) 20
View of Front Panel 21
2.2 LOADING THE CARBON RIBBON 22
Section 2: Installation 23
2.3 LOADING LABELS AND TAGS 25
2.4 REPLACING THE PRINT HEAD 34
CONFIGURATION AND OPERATION 37
3.2 THE OPERATION PANEL 38
3.4 ONLINE AND OFFLINE MODES 41
3.5 USER MODE 42
3.6 INTERFACE MODE 47
3.7 CARTRIDGE MODE 49
3.8 SEMBL MODE 51
3.9 ADVANCED MODE 53
About the Head Check function 56
3.10 HEX DUMP MODE 60
3.11 TEST PRINT MODE 61
3.12 OVERVIEW OF ALL MODES 63
Chart continued on next page 69
CLEANING AND MAINTENANCE 77
Print head 78
4.5 ADJUSTING PRINT QUALITY 80
INTERFACE SPECIFICATIONS 83
Switch No 84
5.7 READY/BUSY 88
5.8 SINGLE JOB BUFFER 89
5.9 MULTI JOB BUFFER 90
5.10 X-ON/X-OFF 91
5.11 SINGLE JOB BUFFER 92
5.12 MULTI JOB BUFFER 93
5.13 DRIVER PROTOCOL 94
Receive, analyze, edit (3) 95
5.13 DRIVER PROTOCOL (CONT’D) 100
5.14 STATUS 3 106
5.15 MULTI JOB BUFFER 107
GT Series Operator’s Manual 108
Page 5-27 109
Page 5-29 111
3) Echo sequence 112
(1) Normal 112
(2) Cancel Request Command 113
5.16 REFERENCE FLOWCHART 114
Basic Specifications 115
Pin Assignments 116
Interface Signals 116
5.18 SINGLE JOB BUFFER 117
Receive, analyze, edit (1) 118
Receive, analyze, edit (2) 118
Receive, ana 118
5.19 MULTI JOB BUFFER 119
Receive, a 120
5.20 IEEE 1284 INTERFACE 122
Pin Assignment 123
5.21 INTERFACE SIGNALS 124
5.22 SINGLE JOB BUFFER 125
5.24 DRIVER PROTOCOL 129
Echo Status Contents 130
TROUBLESHOOTING 135
Section 6: Troubleshooting 136
6.6 LCD WARNING MESSAGES 144
6.7 TROUBLESHOOTING GUIDE 145
No. What to check Remedy 145
Symptom: Low quality print 146
OPTIONAL ACCESSORIES 149
Reinsert the cover 151

Comentarios a estos manuales

Sin comentarios

SATO /gt Series Especificaciones Pagina 46

Comentarios a estos manuales

Relacionado con productos y manuales para Impresión y escaneo SATO /gt Series