SATO M8485S Manual del operador Pagina 135
- Pagina / 228
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Memory Card Function
Expand Memory Area
Command Structure <ESC>EXa
a = Memory Designation
0 Use Printer Memory
1 Use Memory Card Slot 1
2 Use Memory Card Slot 2
Example: <ESC>EX1
Placement: In its own data stream imediately after powering on.
Default: None
Command Function This command expands the memory available to image labels by
using the Memory Card.
Input to Printer
<ESC>A
<ESC>EX2
<ESC>Z
Printer Output There is no printer output as a result of this command.
Special Notes 1. You must have the optional Memory Card to use this command.
Call your local SATO representative for details.
2. When the printer is turned off, the the Memory Card is reset to
normal operation.
3. If the Memory Card specified already contains data, it cannot be
used for memory expansion.
4. The printer will reserve the specified Memory Card for expanded
memory until it is turned off or receives another <ESC>EX
Expand Memory Area command.
5. Use care with Line and Box commands as excessively long lines
can damage the print head.
6. The maximum vertical position that can be specified by the
<ESC>V vertical position command is shown in the table below:
Section 5. Programming Reference
SATO “S” Print Engines 9001034 Rev E Page 5-79
- “S” Applicator 1
- Print Engines 1
- Operator and Technical 1
- Reference Manual 1
- M-8485S OPERATOR’S MANUAL 3
- TABLE OF CONTENTS 5
- SECTION 1 9
- PRINTER OVERVIEW 9
- SPECIFICATIONS 10
- Inside Panel 11
- Section 1. Printer Overview 12
- SECTION 2 17
- INSTALLATION 17
- DIMENSIONS 18
- COMPONENT NAMES 19
- M-8459S Only 19
- M-8460S/M-8485S/M-8490S 19
- REAR PANEL 20
- SWITCHES AND SENSORS 21
- MEDIA LOADING 22
- Section 2. Installation 24
- ADJUSTING THE LABEL SENSOR 25
- OPERATION PANEL 27
- Operation Panel 27
- DIP SWITCH PANEL 28
- SECTION 3 29
- CONFIGURATION 29
- SATO DEFAULT 33
- COMPLETED 33
- POWER ON 34
- Receive Buffer 34
- Hex Dump Label 34
- Print Buffer 34
- PRINT SPEED 36
- PITCH OFFSET 36
- CANCEL PRINT 37
- ZERO SLASH 38
- AUTO ONLINE 38
- VERT. OFFSET 39
- HOR. OFFSET 39
- Label Feed Direction 40
- GAP (X.XV) 41
- INPUT (X 41
- Label Only Eye Mark 42
- Less than 1.0V 2.5V to 3.5V 42
- CALENDAR ENABLED 43
- 01/01/01 01:01 43
- USER TEST PRINT 46
- LARGE SMALL 46
- PRINT SIZE 46
- POTENTIOMETER ADJUSTMENTS 47
- HEX DUMP DIAGNOSTIC LABELS 49
- Print Buffer Hex Label 50
- Receive Buffer Hex Label 50
- SECTION 4 51
- CLEANING AND MAINTENANCE 51
- Paper End Switch 54
- Upper Sensor 54
- Sensor Window 54
- Ribbon Guide Roller 54
- REPLACING THE PRINT HEAD 55
- REPLACING THE FUSE 56
- SECTION 5. PROGRAMMING 57
- USING BASIC 58
- THE PRINT AREA 60
- SATOSATO 63
- COMMAND DEFAULT SETTINGS 64
- OPPOSITE HAND MODELS 65
- M-8485S Left-Hand 65
- COMMAND CODE PAGE REFERENCE 66
- Bar Codes 67
- Input to Printer 68
- UCC-128 Without Incrementing 70
- With Incrementing 70
- Bar Codes, Expansion 72
- Bar Codes, Variable Ratio 73
- Base Reference Point 75
- Characters, Custom-Designed 77
- Character Expansion 79
- Character, Fixed Spacing 81
- Character Pitch 82
- <ESC>* 85
- Continuous Forms Printing 86
- Copy Image Area 87
- Font, Vector 91
- Fonts WB, WL, XB & XL 93
- Form Feed 95
- Form Overlay, Recall 96
- Form Overlay, Store 97
- Graphics, Custom 98
- Graphics, PCX 100
- Job ID Store 101
- Journal Print 102
- Lines and Boxes 103
- Printer Output 104
- Line Feed 105
- Off-Line/Pause 106
- Print Darkness 108
- Print Length, Expanded 109
- Print Position 111
- Print Quantity 113
- Print Speed 114
- Repeat Label 115
- Replace Data (Partial Edit) 116
- Reverse Image 118
- Sequential Numbering 124
- <ESC>A 125
- <ESC>Q50 125
- <ESC>Z 125
- Start/Stop Label 126
- Calendar Option Commands 127
- Calendar Increment 128
- Calendar Print 130
- Calendar Set 132
- Memory Card Option Commands 133
- Memory Card Function 134
- Clear Card Memory 134
- Expand Memory Area 135
- Fonts, TrueType Recall 137
- Fonts, TrueType Store 138
- Format/Field Recall 139
- Format/Field Store 140
- Graphics, Custom Recall 141
- Graphics, Custom Store 142
- Graphics, PCX Recall 144
- Graphics, PCX Store 145
- Initialize 146
- Slot Select 147
- Custom Protocol Command Codes 149
- Download 149
- Two-Dimensional Symbols 151
- Two-Dimensional Bar Codes 152
- Data Matrix, Data Format 152
- Data Matrix, Print Data 154
- Maxicode 157
- SECTION 6 161
- INTERFACE SPECIFICATIONS 161
- RS232C SERIAL INTERFACE 163
- RS232C Interface Signals 164
- CENTRONICS PARALLEL INTERFACE 169
- EXT CONNECTOR 170
- SECTION 7 173
- TROUBLESHOOTING 173
- ERROR SIGNALS 176
- APPENDIX A 177
- COMMAND CODE QUICK REFERENCE 177
- APPENDIX B 189
- BAR CODE SPECIFICATIONS 189
- <ESC>BD0bbcccd (data) d 190
- UPC-A/EAN-13 193
- ODD 024680 194
- EVEN 13579CD 194
- Industrial Two of Five 196
- Matrix Two of Five 197
- Code 128 198
- Example Without incrementing 204
- With incrementing 204
- Data Matrix 206
- Character Set 207
- CODE 128 CHARACTER TABLE 210
- Code 128 Character Table 211
- APPENDIX C 213
- CUSTOM GRAPHICS EXAMPLE 216
- PCX GRAPHICS EXAMPLE 220
- APPENDIX D 221
- OPTIONAL ACCESSORIES 221
- CALENDAR 222
- TOP MOUNTED REFLECTIVE SENSOR 223
- Appendix D: Optional Features 224
- APPENDIX E 225
- CUSTOM PROTOCOL COMMAND CODES 225
- USER DOWNLOAD 226
- ALT PROTOCOL 226
- DEFAULT COMPLETE 226
Relacionado con productos y manuales para Impresoras De Etiquetas SATO M8485S
Impresoras De Etiquetas SATO CL608 Manual de servicio
(245 paginas)
(245 paginas)
Impresoras De Etiquetas SATO CG412 Especificaciones
(100 paginas)
(100 paginas)
Impresoras De Etiquetas SATO CL608 Especificaciones
(58 paginas)
(58 paginas)
Impresoras De Etiquetas SATO CL408e Especificaciones
(10 paginas)
(10 paginas)
Impresoras De Etiquetas SATO LM408e Especificaciones
(86 paginas)
(86 paginas)
Impresoras De Etiquetas SATO TH2 Manual de usuario
(15 paginas)
(15 paginas)
Impresoras De Etiquetas SATO M-8400 Manual del operador
(242 paginas)
(242 paginas)
Impresoras De Etiquetas SATO M8485S Manual del operador
(107 paginas)
(107 paginas)
(87 paginas)
Impresoras De Etiquetas SATO M-10E Especificaciones
(82 paginas)
(82 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales