SATO GL4XXE Manual de servicio Pagina 5
- Pagina / 204
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
iii
TABLE OF CONTENTS (cont’d)
8 CHECKING / ADJUSTMENT PROCEDURES
Performing Test Prints.................................................................................................................... 8-2
Resetting Print Head Data .............................................................................................................. 8-3
Performing Factory Test Prints ....................................................................................................... 8-4
Setting the LCD Contrast................................................................................................................ 8-5
Updating the Printer Firmware........................................................................................................ 8-6
I-MARK / Gap Sensor Adjustments ................................................................................................ 8-7
Thermal Transfer / Direct Thermal Mode Adjustment..................................................................... 8-8
Head Open Sensor CHECKING..................................................................................................... 8-9
Print Darkness Adjustment ............................................................................................................. 8-10
Pitch OFFSET Adjustments (Tear-Off/Cutter/Dispense) ................................................................ 8-11
Pitch Sensor Position Adjustment................................................................................................... 8-12
Print Offset Adjustment................................................................................................................... 8-13
Print Head Alignment...................................................................................................................... 8-14
Print head Pressure Setting............................................................................................................ 8-15
Print Head Pressure Balance Setting ............................................................................................. 8-16
Ribbon Tension Adjustment............................................................................................................ 8-17
Timing Belt Adjustments ................................................................................................................. 8-18
Timing Belt Adjustments (cont’d) .................................................................................................... 8-19
Simple Dispenser Adjustment......................................................................................................... 8-20
Glossary.......................................................................................................................................... 8-21
- GL4xxe Service Manual 1
- O RADIO AND TV RECEPTION 2
- TABLE OF CONTENTS 3
- TABLE OF CONTENTS (cont’d) 4
- INTRODUCTION 7
- ABOUT THIS MANUAL 8
- GENERAL DESCRIPTION 9
- THEORY OF OPERATION 10
- CONTROL FEATURES 11
- Unit 1: Introduction 12
- GL4xxe Series Service Manual 12
- TECHNICAL DATA 13
- Unit 2: Technical Data 14
- REGULATORY 15
- CHARACTER FONT CAPABILITIES 16
- BARCODE CAPABILTIES 17
- INTERFACE 18
- SPECIFICATIONS 18
- INTERFACE SPECIFICATIONS 19
- SUPPORTED PROTOCOLS 20
- READY/BUSY INTERFACE SIGNALS 21
- IEEE1284 PARALLEL INTERFACE 22
- Table of IEEE1284 signals 23
- UNIVERSAL SERIAL BUS (USB) 25
- SOFTWARE SPECIFICATIONS 26
- 802.11G WIRELESS 27
- ALL INTERFACES 28
- RECEIVE BUFFER CONTROL 29
- STATUS5 TIMING CHARTS 29
- NORMAL PROCESS 29
- CANCEL PROCESS 29
- ERROR PROCESS 29
- PRINT PROCESS 30
- COMMAND PROCESS 30
- BCC ERROR PROCESS 30
- CHARTS AND DIAGRAMS 31
- PRINT SETUP DIMENSIONS 32
- LABEL PRINT DIRECTION 33
- LABEL ADJUSTMENT DIAGRAM 34
- READY/BUSY TIMING CHARTS 35
- X-ON/X-OFF TIMING CHARTS 36
- Unit 4: Charts And Diagrams 37
- CONFIGURATION 39
- PRINTER CONFIGURATION 40
- CONFIGURATION MODES 41
- CONFIGURATION MODE 42
- ADVANCED MODE 43
- SERIAL INTERFACE MODE 45
- PARALLEL INTERFACE MODE 46
- CENTRONICS INTERFACE MODE 47
- PGL EMULATION MODE 51
- ZGL EMULATION MODE 52
- DGL EMULATION MODE 53
- TGL EMULATION MODE 54
- IGL EMULATION MODE 55
- DIAGNOSTICS MODE 56
- PRINTER MANAGEMENT MODE 57
- MISC QUICK MENUS 58
- SOFT RESET 59
- KEY LOCK/UNLOCK 59
- MENU DEFINITION TABLES 60
- USER MODE (TABLE 4-1) 61
- ADVANCED MODE (TABLE 4-3) 67
- Data Protocol 80
- Buffer Size in K 80
- INTERFACES 90
- MENU DESCRIPTION 100
- EMULATION 101
- DIAGNOSTICS 120
- Priority Setting 120
- Command* 120
- IGL Setup 120
- Save state* 120
- Error Log Clear 122
- TROUBLESHOOTING 127
- ERROR TROUBLESHOOTING 128
- ERROR MESSAGES 129
- TROUBLESHOOTING TABLE 134
- NO PRINTED IMAGE 135
- INCORRECT LABEL POSITIONING 135
- SMEARED PRINT IMAGES 135
- INTERFACE TROUBLESHOOTING 136
- LAN ETHERNET INTERFACE 137
- 802.11G WIRELESS INTERFACE 137
- CENTRONICS INTERFACE 137
- TEST PRINT TROUBLESHOOTING 138
- Figure 6-2, Sample Test Label 139
- REPLACEMENT 140
- PROCEDURES 140
- REPLACEMENT PROCEDURES 141
- PLATEN ROLLER REPLACEMENT 142
- LABEL SENSOR REPLACEMENTS 143
- MAIN PCB REPLACEMENT 145
- POWER SUPPLY REPLACEMENT 147
- PCB during reassembly 148
- TIMING BELT REPLACEMENT 149
- RIBBON SENSOR REPLACEMENT 153
- HEAD-OPEN SENSOR REPLACEMENT 154
- RIBBON BOSS/TORQUE LIMITER 155
- Note the 156
- MEMORY CARTRIDGE REPLACEMENT 157
- INTERFACE BOARD REPLACEMENT 158
- CUTTER KIT REPLACEMENT 159
- REAL-TIME CLOCK REPLACEMENT 160
- Original front cover 162
- Figure 7-26, Replacement 170
- CHECKING / ADJUSTMENT 174
- PERFORMING TEST PRINTS 175
- RESETTING PRINT HEAD DATA 176
- SETTING THE LCD CONTRAST 178
- UPDATING THE PRINTER FIRMWARE 179
- HEAD OPEN SENSOR CHECKING 182
- PRINT DARKNESS ADJUSTMENT 183
- Pitch sensor holder 185
- I-Mark sensor position 185
- Gap Sensor position 185
- PRINT OFFSET ADJUSTMENT 186
- PRINT HEAD ALIGNMENT 187
- PRINT HEAD PRESSURE SETTING 188
- RIBBON TENSION ADJUSTMENT 190
- TIMING BELT ADJUSTMENTS 191
- SIMPLE DISPENSER ADJUSTMENT 193
- GLOSSARY 194
Relacionado con productos y manuales para Impresión y escaneo SATO GL4XXE
Impresión y escaneo SATO LM408e Manual de servicio
(98 paginas)
(98 paginas)
Impresión y escaneo SATO XL4xxe Manual de usuario
(114 paginas)
(114 paginas)
Impresión y escaneo SATO CL608 Especificaciones
(12 paginas)
(12 paginas)
Impresión y escaneo SATO GY412 Manual de instrucciones
(217 paginas)
(217 paginas)
Impresión y escaneo SATO XL400 Manual de usuario
(194 paginas)
(194 paginas)
Impresión y escaneo SATO M8485Se Manual de servicio
(216 paginas)
(216 paginas)
Impresión y escaneo SATO CG412TT Manual de usuario
(102 paginas)
(102 paginas)
Impresión y escaneo SATO XL4xxe Manual de usuario
(121 paginas)
(121 paginas)
(73 paginas)
Impresión y escaneo SATO M8450 Manual de usuario
(60 paginas)
(60 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales